Anca AMD2000 Series User Manual Page 24
- Page / 189
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
AMD2000 Series - Servo Drive - User Manual
24 DS619-0-00-0019 - Rev 0 ANCA Motion
Drive Display
Indicator
5 x 7-segment LED
Operator interfacing
4 DIP buttons
The 7 segment LED display on the AMD2000 serves three functions. It is used to report errors, to
indicate the state of the EtherCAT communications and to indicate the state of the drive.
The dots represent wire saving encoder UVW sensor feedback state on power up.
Error state 3.6.12.9
In an error condition, the display will read either E-### where ### refers to the relevant error
code. See section 11 Fault Tracing for the description and possible causes for the error.
When no error has been reported, the display will provide information on both the drive state
and the communications state.
Communications state 3.6.12.10
To indicate the state of the EtherCAT communications, the leftmost digits of the display will
read C#, where # refers to the current communications condition as shown in the following
table:
C#
Communications State
C0
None
C1
Initialization
C2
Pre-operational
C4
Safe-operational
C8
Operational
Drive state 3.6.12.11
To indicate the state of the drive, the rightmost digits of the display will read d#, where # refers to the
current drive condition as shown in the following table:
d#
Drive State
d0
Off
d2
Ready to operate
d3
Enabling
d4
Enabled
- AMD2000 Series - Servo Drive 1
- Contents 4
- 1. Safety 10
- Safety 11
- 2. Introduction 12
- 2.1.15 Related Documents 13
- 2.1.17 Trademarks 13
- 3. Product Overview 14
- 3.3 Operating Principle 15
- D2009-2S1-A 16
- 3.5 System Overview 17
- Product Overview 19
- 3.6 Connector Overview 20
- 3.6.12 AMD2000 9A 21
- 3.6.12.4 22
- 3.6.12.7 23
- 4. Mechanical Installation 25
- Mechanical Installation 27
- 4.4 Installation 28
- STEP2 STEP 3 STEP 4 29
- Thermal Overload 5.5.11.1 31
- 5.6 Power Cable Selection 32
- 5.7 Control Cable Selection 33
- 5.8 Cable Routing 33
- 6. Power Wiring 35
- Power Wiring 37
- Heatsink 38
- PE connection 38
- 6.6 Power Supply Filters 41
- 6.8 Motor Connections 44
- 6.8.12.1 45
- Protective Earth Wire to 47
- Metal P-Clip 49
- Exposed Metal Braid 49
- Armature Cable from 3A 49
- 6.9 Drive Output Filters 50
- 6.10 Motor Brake Connection 52
- 6.11 Motor Thermal Switch 52
- 6.12 Motor Thermal Sensor 53
- 7. Control Wiring 55
- 7.2.12 Analogue Outputs 57
- 7.3 Digital I/O 58
- 7.3.12.1 59
- 7.3.12.1.2 60
- 7.3.12.2.2 60
- Digital Outputs 7.3.12.3 61
- 7.6.11 EtherCAT® 62
- EtherCAT 63
- Slave Controller 63
- 7.8 Motor Feedback 65
- 7.7 DIP Buttons 65
- Control Wiring 67
- 8. Installation Checklist 68
- Installation Checklist 69
- 9. Start-up 70
- 9.6 Starting the AMD2000 71
- Start-up 73
- 9.8.11 ANCA MotionBench 77
- 10. Feature Configuration 87
- Figure 10-1 Circle Graph Tab 89
- Figure 10-2 Time Domain Tab 89
- 10.1.15 Drive Bypass Mode 97
- ANCA Motion 100
- Feature Configuration 101
- 10.1.17 Encoders 103
- S-0-0151 / 151 115
- S-0-0403 / 403 115
- P-0-0257 / 33025 119
- 10.1.20 Modulo Operation 121
- 10.1.22 Motor Control 129
- P-0-033 / 32801 131
- P-0-034 / 32802 131
- – EOL calibrated 131
- If Motor Type =PMSM 133
- Field Weakening 133
- 10.1.23 Operating Modes 139
- 11. Fault Tracing 144
- 11.3 Supported Error Codes 145
- Fault Tracing 147
- Error E0007 148
- Too Many Errors I0666 156
- Task Overrun W1002 156
- 12. Technical Data 158
- Technical Data 159
- 12.3.16 Analogue Inputs 161
- 12.3.17 Analogue Outputs 161
- 12.3.19 Encoder Channel 1 161
- 12.4.12 Digital servo drive 163
- 12.6.11 Storage 165
- 12.6.12 Transport 165
- 12.6.15 Cooling 165
- 12.7 Dimension Drawings 166
- 12.10 Temperature De-rating 169
- 12.12 Discharge Period 171
- 12.13 Motor Output Power 171
- 12.15 Materials 174
- 12.16 Standards Conformity 175
- 12.17 EtherCAT® 176
- Conformance Marking 176
- 12.18 CE Marking 176
- Definitions 12.18.12.1 177
- M A 6 0 - 0 6 3 0 - A B 180
- K 2 A - F S P D - 0 2 0 183
- 13.4 Other Accessories 184
- 13.4.12 EtherCAT Cables 185
- 13.4.14 AMD2000 3A EMC Kit 185
- 13.4.15 AMD2000 9A EMC Kit 185
- 13.5 Starter Kits 186
- Accessories 187
- 14. Additional Information 188
- 14.4 Feedback 189
© 2020, manymanuals.com. All rights reserved. | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals